Manage cookies

We use cookies to improve our services. Read more about how we use cookies and how you can refuse them.

The necessary cookies help to make the website work properly.

Anonymous statistical cookies help to understand how visitors use the website.

  • MicroPython
    3 min | 5439

    #MicroPython: an IoT BRIO Locomotive

    MicroPython | 3 min | 5439


    This tutorial helps you update a BRIO locomotive using an ESP32 that runs MicroPython. As a result, you can control the speed of the BRIO using a cell phone or a laptop (basically, everything that has a browser).

    If you don't know what a BRIO locomotive is, check out the following picture:

    BRIO World 33594
    Fig. 1: BRIO World 33594

    In this tutorial, I will try to accomplish the following points:

    1. Hardware modifications on a ESP32 board;
    2. MicroPython installation;
    3. Controlling the locomotive speed using a web browser.

    The results can be seen in the following video (turn on the sound!):

    Software and Hardware

    The following hardware and software will be used in this tutorial:

    Hardware Modifications

    This setup is only to control the speed of the BRIO (start and stop too). If you need to control direction (forward or backward), you need to use an H-bridge configuration.

    Unfortunately, inside the BRIO there isn't enough space to mount an ESP32 and a 3.7V battery. Thus, the ESP32 board with the battery are outside and will be transported on a second wagon (BRIO World 33406). The BRIO locomotive needs a 1.5v AAA battery and, as you see in the hardware list, the ICR18650 is listed. That is a 3.7v Li-ion battery. The battery will power the ESP32 board and throughout a PWM signal the motor and light of the BRIO locomotive. The ESP32 pin maximal current is not enough to supply the motor and the light so you'll need an NPN MOSFET (Fig. 2).

    mosfet.png
    Fig. 2: MOSFET pin description

    You need to connect pin 1 of the MOSFET (Vin) to a pin of the ESP32 and pin 2 (GND) to the ground of the board. In Fig. 2a, you can see that I am using a WeMos board. But that board is no longer available. Moreover, it only has 512kB RAM, which is very limited. That's why I listed the board shown in Fig. 2b. You can solder the SOT-23 NPN MOSFET between (check the red dashed boxes on Fig. 2b):

    • pin 12 and GND (pointing to the board inside)
    • pin 19 & GND (pointing to the board inside)
    • pin 23 & GND (pointing to the board inside)
    • pin 13 & GND (pointing to the board outside)
    • GND & pin 21 (pointing to the board outside)

    pin 3 of the MOSFET (Vout) is connected to positive + battery terminal of the BRIO (green), and a second cable (blue) connects the negative - battery terminal of the BRIO to the ESP32 + battery terminal (check Fig. 2a). You can switch the polarity on the BRIO, the motor and the light will work anyway. You can use a hot glue gun to fix the MOSFET to the board as you see in Fig. 1a.


    Fig. 2a: BRIO and ESP32 connection

    Fig. 2b: ESP32 8MB RAM

    MicroPython Installation

    Download a MicroPython firmware image. If you bought the ESP32 board with 8MB RAM that I listed before, you should download the firmware with SPIRAM support. Otherwise, you won't see the extra MBs of RAM.

    Then, connect the board to a USB port on your host PC and flash the ESP using the esptool.

    esptool.py --chip esp32 --port /dev/ttyUSB0 erase_flash
    esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 460800 write_flash -z 0x1000 esp32-idf3-20191220-v1.12.bin

    You can check this tutorial for more information: Tutorial: Getting started with MicroPython. If you are a MicroPython newby, I recommend you to read this article too: MicroPython: Visual Studio Code as IDE.

    BRIO Locomotive Speed Contol

    Clone the following repository:

    git clone https://github.com/lemariva/uPyTrain.git

    and rename the boot.py.sample to boot.py and add your Wi-Fi credentials:

    ssid_ = ''
    wpa2_pass = ''

    This enables the BRIO locomotive to connect to Wi-Fi. Upload the code to the ESP32 using VSCode and the PyMakr extension (if you don't understand this, check this tutorial.)

    The ESP32 should connect to the Wi-Fi. Then, open a browser and visit the IP address listed on the VSCode Terminal: You should get Fig. 3 and the speed control is shown in the article video listed above.

    train_web.png
    Fig. 3: Website to control the BRIO locomotive speed

    Conclusion

    This tutorial helps you upgrade a BRIO locomotive to connect it to Wi-Fi and control its speed. The ESP32 running MicroPython offers a small website and, through a GET request, you can set the PWM duty cycle, resulting in the speed of the locomotive. Have FUN!


    Comments

    Thomas S 06.15.2020

    Great post - exactly what I've been looking for! Does the ESP32 board have a BMS to avoid discharging the Liion cell to low and maybe even load the cell via the microUSB port?

    Thanks, Thomas